ON-BOARD DIAGNOSTIC SYSTEM FUNCTION (DYNAMIC STABILITY CONTROL)


BHE040243000T02

Malfunction Detection Function

• The malfunction detection function detects malfunctions in the input/output signal system of the DSC HU/CM when the ignition switch is at the ON position.

• When the DSC HU/CM are started up, the following malfunction detections are performed.

– The ABS and brake system warning lights, DSC OFF and DSC indicator lights illuminate for approx. 3 s when the ignition switch is turned to the ON position to inspect for open circuits in the lights. At the same time, the fail-safe relay is operated, and the input/output signals of each part is monitored for malfunction diagnosis. After starting to drive, the first time the vehicle speed is approx. 10 km/h {6.2 mph} or more the pump motor is operated and malfunction diagnosis is performed again.

• When malfunctions are detected, the corresponding lights are illuminated to alert the driver. Using the external tester communication function, DTCs can be output through the DLC-2 terminal KLN. At the same time, malfunction detection results are sent to the memory and fail-safe functions.

Memory Function

• The memory function stores DTCs of malfunctions in input/output signal systems. With this function, once a DTC is stored it is not cleared after the ignition switch has been turned off (LOCK position), even if the malfunctioning signal system has returned to normal.

• Since the DSC HU/CM has a built-in non-volatile memory, DTCs are not cleared even if the battery is removed. Therefore, it is necessary to clear the memory after performing repairs. Refer to the Workshop Manual for the DTC clearing procedure.

Fail-safe Function

• When the malfunction detection function determines a malfunction, each light illuminates to advise the driver. At this time, the fail-safe function controls the ABS, EBD, TCS and DSC as shown in the fail-safe function table.

Warning
• If EBD control is suspended the rear wheels could lock-up before the front wheels. If this occurs, the vehicle could swerve and become unstable. Therefore always inspect the system immediately if EBD control is suspended.

Fail-safe Function Malfunction Contents

Malfunction location

DTC number

Fail-safe function

Warning light illumination status

Control status

WDS or equivalent

Display

ABS warning light

Brake system warning light (when parking brake is released)

DSC indicator light

DSC OFF light

ABS control

EBD

Control

TCS control

DSC control

Power supply system
B1318
Illuminated

*1

Not illuminated
Illuminated

*1

Not illuminated
Control disabled

*2

Control enabled
Control disabled

*2

Control disabled

*2

DSC HU/CM system
B1342
Illuminated
Illuminated
Illuminated
Illuminated
Control disabled
Control disabled
Control disabled
Control disabled
Brake switch signal system
B1484
Illuminated
Not illuminated
Illuminated
Not illuminated
Control disabled
Control enabled
Control disabled
Control disabled
C1953
DSC HU/CM configuration system
B2477
Illuminated
Not illuminated
Illuminated
Not illuminated
Control disabled
Control enabled
Control disabled
Control disabled
DSC OFF switch system
C1093
Not illuminated
Not illuminated
Illuminated
Illuminated
Control enabled
Control enabled
Control disabled
Control disabled
Pump motor, motor relay systems
C1095
Illuminated
Not illuminated
Illuminated
Not illuminated
Control disabled
Control enabled
Control disabled
Control disabled
C1096
PCM communication system
C1119
Not illuminated
Not illuminated
Illuminated
Not illuminated
Control enabled
Control enabled
Control disabled
Control disabled
C1134
ABS wheel-speed sensor system
C1145
Illuminated
Not illuminated
Illuminated
Not illuminated
Control disabled
Control enabled
Control disabled
Control disabled
C1155
C1165
C1175
C1233
C1234
C1235
C1236
ABS wheel-speed sensor/ABS sensor rotor systems
C1148
Illuminated
Not illuminated
Illuminated
Not illuminated
Control disabled
Control enabled
Control disabled
Control disabled
C1158
C1168
C1178
ABS wheel-speed sensor (slip monitor) system
C1222
Illuminated
Illuminated
Illuminated
Not illuminated
Control disabled
Control disabled
Control disabled
Control disabled
Valve relay system
C1186
Illuminated
Illuminated
Illuminated
Not illuminated
Control disabled
Control disabled
Control disabled
Control disabled
C1266
Solenoid valve system
C1194
Illuminated
Illuminated
Illuminated
Not illuminated
Control disabled
Control disabled
Control disabled
Control disabled
C1198
C1210
C1214
C1242
C1246
C1250
C1254
C1400
C1410
C1957
C1958
Brake fluid pressure sensor system
C1288
Illuminated
Not illuminated
Illuminated
Not illuminated
Control disabled
Control enabled
Control disabled
Control disabled
C1290
C1440
C1730
C1954
Steering angle sensor system
C1295
Not illuminated
Not illuminated
Illuminated
Not illuminated
Control enabled
Control enabled
Control disabled
Control disabled
C1306
C1307
C1937
C1938
C1956
C2778
Combined sensor system
C1279
Not illuminated
Not illuminated
Illuminated
Not illuminated
Control enabled
Control enabled
Control disabled
Control disabled
C1280
C1281
C1282
C1951
C1952
C1959
C2768
Incorrect DSC HU/CM installed
C1805
Illuminated
Not illuminated
Illuminated
Not illuminated
Control disabled
Control enabled
Control disabled
Control disabled
DSC HU/CM control system
C1994
Illuminated

*3

Not illuminated
Illuminated

*3

Not illuminated
Control disabled

*4

Control enabled
Control disabled

*4

Control disabled

*4

CAN communication system
U1900
Not illuminated

*5

Not illuminated
Illuminated
Illuminated
Control enabled

*6

Control enabled
Control disabled
Control disabled
U2516
Illuminated
Not illuminated
Illuminated
Not illuminated
Control disabled
Control enabled
Control disabled
Control disabled
*1 :
If the ignition voltage returns to normal, the light goes out.
*2 :
If the ignition voltage returns to normal, control is enabled.
*3 :
Light goes out if the malfunction is repaired.
*4 :
Control enabled if the malfunction is repaired.
*5 :
Illuminates if tire size data cannot be received.
*6 :
Control is disabled if tire size data cannot be received.